FreeBSD on PinePhone Pro. serial debug cable - mine is a 3-pin type to 3 positions female header pinout ``` tip - white (RX from pinephone) ring - red (TX from pinephone) base - black (GND) ``` baud rate is 1500000 instead of 115200, 8n1. nanoUART pinout - top to bottom front side (pins to the right) ``` GND TX RX DTR RTS 3V3 ``` back side (pins to the left) ``` RI CTS DSR DCD VREF 5V ``` back to [main](../) PinePhone Pro page. ## Links [FreeBSD on the PinePhone Pro](https://codeberg.org/Honeyguide/freebsd-pinephonepro), ### local links [c2](/machines/gigabyte_b450m_ds3h/freebsd), [nanoUART](/microcontrollers/nanouart), ## History 2026-10-05: ppp - it also shows loads of these messages ``` rk_tsadc0: Alarm: device temperature is above of alarm level. rk_tsadc0: Alarm: device temperature is above of alarm level. rk_tsadc0: Alarm: device temperature is above of alarm level. rk_tsadc0: Alarm: device temperature is above of alarm level. ``` 2026-10-05: ppp - today I tried plugging in two different usb hubs, just to see if they were detected. They were not. usbconfig reports this ```sh root@PinePhonePro-FreeBSD:~ # usbconfig ugen0.1: at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen1.1: at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA) ugen2.1: at usbus2, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen3.1: at usbus3, cfg=0 md=HOST spd=FULL (12Mbps) pwr=SAVE (0mA) ugen4.1: at usbus4, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=SAVE (0mA) ``` doesn't matter if a usb hub is plugged in or not. 2026-10-04: ppp - shutdown info ```sh root@PinePhonePro-FreeBSD:~ # shutdown -p now Shutdown NOW! shutdown: [pid 801] root@PinePhonePro-FreeBSD:~ # *** FINAL System shutdown message from root@PinePhonePro-FreeBSD *** System going down IMMEDIATELY System shutdown time has arrived Waiting (max 60 seconds) for system process `vnlru' to stop... done Waiting (max 60 seconds) for system process `syncer' to stop... Syncing disks, vnodes remaining... 0 0 0 0 0 0 0 0 done All buffers synced. Uptime: 1h11m43s rk818_pmu0: Powering off... ``` 2026-10-04: ppp - now resize the root filesystem ```sh root@PinePhonePro-FreeBSD:~ # df -h / Filesystem Size Used Avail Capacity Mounted on /dev/ufs/FreeBSD_Install 8.2G 6.7G 839M 89% / root@PinePhonePro-FreeBSD:~ # growfs / Device is mounted read-write; resizing will result in temporary write suspension for /. It's strongly recommended to make a backup before growing the file system. OK to grow filesystem on /dev/ufs/FreeBSD_Install, mounted on /, from 8.3GB to 58GB? [yes/no] yes super-block backups (for fsck_ffs -b #) at: 18168384, 19033536, 19898688, 20763840, 21628992, 22494144, 23359296, 24224448, 25089600, 25954752, 26819904, 27685056, 28550208, 29415360, 30280512, 31145664, 32010816, 32875968, 33741120, 34606272, 35471424, 36336576, 37201728, 38066880, 38932032, 39797184, 40662336, 41527488, 42392640, 43257792, 44122944, 44988096, 45853248, 46718400, 47583552, 48448704, 49313856, 50179008, 51044160, 51909312, 52774464, 53639616, 54504768, 55369920, 56235072, 57100224, 57965376, 58830528, 59695680, 60560832, 61425984, 62291136, 63156288, 64021440, 64886592, 65751744, 66616896, 67482048, 68347200, 69212352, 70077504, 70942656, 71807808, 72672960, 73538112, 74403264, 75268416, 76133568, 76998720, 77863872, 78729024, 79594176, 80459328, 81324480, 82189632, 83054784, 83919936, 84785088, 85650240, 86515392, 87380544, 88245696, 89110848, 89976000, 90841152, 91706304, 92571456, 93436608, 94301760, 95166912, 96032064, 96897216, 97762368, 98627520, 99492672, 100357824, 101222976, 102088128, 102953280, 103818432, 104683584, 105548736, 106413888, 107279040, 108144192, 109009344, 109874496, 110739648, 111604800, 112469952, 113335104, 114200256, 115065408, 115930560, 116795712, 117660864, 118526016, 119391168, 120256320, 121121472, 121986624 root@PinePhonePro-FreeBSD:~ # df -h / Filesystem Size Used Avail Capacity Mounted on /dev/ufs/FreeBSD_Install 58G 6.7G 46G 13% / ``` 2026-10-04: ppp - recover GPT partition table, and resize the ufs partition ```sh root@PinePhonePro-FreeBSD:~ # gpart recover mmcsd0 mmcsd0 recovered root@PinePhonePro-FreeBSD:~ # gpart show -p mmcsd0 => 34 122167222 mmcsd0 GPT (58G) 34 66584 mmcsd0p1 efi (33M) 66618 17407998 mmcsd0p2 freebsd-ufs (8.3G) 17474616 104692640 - free - (50G) root@PinePhonePro-FreeBSD:~ # gpart resize -i 2 mmcsd0 mmcsd0p2 resized root@PinePhonePro-FreeBSD:~ # gpart show -p mmcsd0 => 34 122167222 mmcsd0 GPT (58G) 34 66584 mmcsd0p1 efi (33M) 66618 122092486 mmcsd0p2 freebsd-ufs (58G) 122159104 8152 - free - (4.0M) ``` 2026-10-04: ppp - disk layout - the microSD card seems to be this ```sh root@PinePhonePro-FreeBSD:~ # gpart show -p mmcsd0 => 34 18874294 mmcsd0 GPT (58G) [CORRUPT] 34 66584 mmcsd0p1 efi (33M) 66618 17407998 mmcsd0p2 freebsd-ufs (8.3G) 17474616 1399712 - free - (683M) ``` and the eMMC this ```sh root@PinePhonePro-FreeBSD:~ # gpart show -p mmcsd1 => 63 241663937 mmcsd1 MBR (115G) 63 62437 - free - (30M) 62500 437501 mmcsd1s1 linux-data (214M) 500001 15500000 mmcsd1s2 linux-data (7.4G) 16000001 225663999 mmcsd1s3 linux-data (108G) ``` 2026-10-04: ppp - some interesting messages from dmesg ``` warning: KLD '/boot/kernel/kernel' is newer than the linker.hints file KLD mx25l.ko: depends on kernel - not available or version mismatch ``` ok, this is the [mx25l(4)](https://man.freebsd.org/cgi/man.cgi?query=mx25l) driver fro spi flash chips. and ``` goodix_touch0: at addr 0x28 irq 81 on iicbus0 goodix_touch0: Setting up evdev... goodix_touch0: Touchscreen size X: 720 goodix_touch0: Touchscreen size Y: 1440 goodix_touch0: Product ID: 1 1 5 8 goodix_touch0: F/w version: 0 1 goodix_touch0: X-res: 42 1 goodix_touch0: Y-res: 2 0 goodix_touch0: Vendor ID: 0 3 goodix_touch0: Goodix touch driver loaded ``` 2026-10-04: c2 - the nanoUART shows up on my workstation ```sh root@kg-core2:~ # ls -l /dev/cuaU* /dev/ttyU* crw-rw---- 1 uucp dialer 0x22e Oct 4 19:20 /dev/cuaU0 crw-rw---- 1 uucp dialer 0x231 Oct 4 19:20 /dev/cuaU0.init crw-rw---- 1 uucp dialer 0x232 Oct 4 19:20 /dev/cuaU0.lock crw------- 1 root wheel 0x22b Oct 4 19:20 /dev/ttyU0 crw------- 1 root wheel 0x22c Oct 4 19:20 /dev/ttyU0.init crw------- 1 root wheel 0x22d Oct 4 19:20 /dev/ttyU0.lock ``` so I should be able to make cu work like this ```sh tingo@kg-core2:/zt/t2/doc/Pine64/PinePhone_Pro/freebsd $ sudo cu -s 1500000 -l /dev/cuaU0 Connected ``` (using sudo until I can log out / in and get my groups updated) and it works, some output captured ``` rk2aw: booted version RK3399/pinephone-pro/2024-02-14/00:29:35 rk2aw: Booted from source 3 (SPI NOR) block=0x00 rk2aw: Will try booting boot block 0x01 on SPI NOR U-Boot TPL 2024.04-rc1-megi-ppp-00176-g6dc0a49f522d-dirty (Feb 15 2024 - 22:51:46) Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2024.04-rc1-megi-ppp-00176-g6dc0a49f522d-dirty (Feb 15 2024 - 22:51:46 +0100) Battery status: vol=3875 cur=-265 ocv=3941 plugin=0 status=off usb_fault=1 usb_exist=0 bat_exist=1 Trying to boot from SPI spl_perform_fixups: could not map boot_device to ofpath: -19 U-Boot 2024.04-rc1-megi-ppp-00176-g6dc0a49f522d-dirty (Feb 15 2024 - 22:51:46 +0100) SoC: Rockchip rk3399 Reset cause: POR Model: Pine64 PinePhonePro DRAM: 4 GiB (effective 3.9 GiB) PMIC: RK8180 (on=0x80, off=0x08) Core: 331 devices, 37 uclasses, devicetree: separate MMC: mmc@fe320000: 1, mmc@fe330000: 0 Loading Environment from nowhere... OK In: serial,usbkbd Out: serial,vidconsole Err: serial,vidconsole Model: Pine64 PinePhonePro Booting /efi\boot\bootaa64.efi ``` a bit later ``` Consoles: EFI console Reading loader env vars from /efi/freebsd/loader.env Setting currdev to disk0p1: FreeBSD/arm64 EFI loader, Revision 3.0 (Fri Jan 24 00:28:10 UTC 2025 root@releng3.nyi.freebsd.org) Command line arguments: loader.efi Image base: 0xf48ee000 EFI version: 2.100 EFI Firmware: Das U-Boot (rev 8228.1024) Console: efi,comconsole (0) Load Path: /efi\boot\bootaa64.efi Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,0000000000000000)/SD(1)/SD(0)/HD(1,GPT,8230dfcc-da01-11ef-81ea-0cc47ad8b808,0x22,0x10418) BootOrder: 0000 0001 Trying ESP: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,0000000000000000)/SD(1)/SD(0)/HD(1,GPT,8230dfcc-da01-11ef-81ea-0cc47ad8b808,0x22,0x10418) Setting currdev to disk0p1: Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b,0000000000000000)/SD(1)/SD(0)/HD(2,GPT,8230dfd0-da01-11ef-81ea-0cc47ad8b808,0x1043a,0x1099ffe) Setting currdev to disk0p2: Loading /boot/defaults/loader.conf Loading /boot/defaults/loader.conf Loading /boot/device.hints Loading /boot/loader.conf Loading /boot/loader.conf.local c\ ______ ____ _____ _____ | ____| | _ \ / ____| __ \ | |___ _ __ ___ ___ | |_) | (___ | | | | | ___| '__/ _ \/ _ \| _ < \___ \| | | | | | | | | __/ __/| |_) |____) | |__| | | | | | | | || | | | |_| |_| \___|\___||____/|_____/|_____/ +-------- Welcome to FreeBSD ----------+ ``` ` | | s` `.....---.......--.``` -/ | 1. Boot Multi user [Enter] | +o .--` /y:` +. | 2. Boot Single user | yo`:. :o `+- | 3. Escape to loader prompt | y/ -/` -o/ | 4. Reboot | .- ::/sy+:. | 5. Cons: Dual (Serial primary) | / `-- / | | `: :` | Kernel: | `: :` | 6. kernel (1 of 1) | / / | | .- -. | Options: | -- -. | 7. Boot Options | `:` `:` | | .-- `--. +--------------------------------------+ .---.....----. Autoboot in 0 seconds. [Space] to pause Loading kernel... /boot/kernel/kernel data=0x13b0620+0x36b9e0 0x8+0x11b800+0x8+0xee013 Loading configured modules... /boot/dtb/rk3399-pinephone-pro.dtb size=0x16e78 can't find '/etc/hostid' /boot/entropy size=0x1000 Using DTB from loaded file '/boot/dtb/rk3399-pinephone-pro.dtb'. Loading splash ok EFI framebuffer information: addr, size 0xf7b00000, 0x3f4800 dimensions 720 x 1440 stride 720 masks 0x00ff0000, 0x0000ff00, 0x000000ff, 0xff000000 ---<>--- GDB: debug ports: uart GDB: current port: uart KDB: debugger backends: ddb gdb KDB: current backend: ddb Copyright (c) 1992-2025 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 15.0-CURRENT #75 main-b836c229aa5a-dirty: Wed Apr 16 15:16:46 SAST 2025 toby@toby-ghostbsd:/home/toby/Data/home/toby/Projects/freebsd-pinephonepro/obj/home/toby/Data/home/toby/Projects/freebsd-pinephonepro/freebsd-src/arm64.aarch64/sys/PINEPHONE_PRO arm64 gcc version 14.1.0 (FreeBSD Ports Collection for aarch64) WARNING: WITNESS option enabled, expect reduced performance. VT(efifb): resolution 720x1440 real memory = 4154503168 (3962 MB) avail memory = 4015398912 (3829 MB) Starting CPU 1 (1) Starting CPU 2 (2) Starting CPU 3 (3) Starting CPU 4 (100) Starting CPU 5 (101) FreeBSD/SMP: Multiprocessor System Detected: 6 CPUs random: unblocking device. random: entropy device external interface kbd0 at kbdmux0 ofwbus0: rk_grf0: mem 0xff320000-0xff320fff on ofwbus0 rk3399_pmucru0: mem 0xff750000-0xff750fff on ofwbus0 rk3399_cru0: mem 0xff760000-0xff760fff on ofwbus0 rk_grf1: mem 0xff770000-0xff77ffff on ofwbus0 regfix0: on ofwbus0 regfix1: on ofwbus0 regfix2: on ofwbus0 regfix3: on ofwbus0 regfix4: on ofwbus0 regfix5: on ofwbus0 regfix6: on ofwbus0 regfix7: on ofwbus0 regfix8: on ofwbus0 regfix9: on ofwbus0 debug0: mem 0xfe430000-0xfe430fff on ofwbus0 debug1: mem 0xfe432000-0xfe432fff on ofwbus0 debug2: mem 0xfe434000-0xfe434fff on ofwbus0 debug3: mem 0xfe436000-0xfe436fff on ofwbus0 debug4: mem 0xfe610000-0xfe610fff on ofwbus0 debug5: mem 0xfe710000-0xfe710fff on ofwbus0 simple_mfd0: mem 0xff310000-0xff310fff on ofwbus0 psci0: on ofwbus0 smccc0: on psci0 gic0: mem 0xfee00000-0xfee0ffff,0xfef00000-0xfefbffff,0xfff00000-0xfff0ffff,0xfff10000-0xfff1ffff,0xfff20000-0xfff2ffff irq 18 on ofwbus0 its0: mem 0xfee20000-0xfee3ffff on gic0 rk_pinctrl0: on ofwbus0 gpio0: mem 0xff720000-0xff7200ff irq 76 on rk_pinctrl0 gpiobus0: on gpio0 gpio1: mem 0xff730000-0xff7300ff irq 77 on rk_pinctrl0 gpiobus1: on gpio1 gpio2: mem 0xff780000-0xff7800ff irq 78 on rk_pinctrl0 gpiobus2: on gpio2 gpio3: mem 0xff788000-0xff7880ff irq 79 on rk_pinctrl0 gpiobus3: on gpio3 gpio4: mem 0xff790000-0xff7900ff irq 80 on rk_pinctrl0 gpiobus4: on gpio4 rk_i2c0: mem 0xff130000-0xff130fff irq 24 on ofwbus0 iicbus0: on rk_i2c0 rk_i2c1: mem 0xff3c0000-0xff3c0fff irq 40 on ofwbus0 iicbus1: on rk_i2c1 rk818_pmu0: at addr 0x38 irq 83 on iicbus1 rk818_pmu0: RK818 battery driver loaded fan53555_pmic0: at addr 0x80 on iicbus1 fan53555_pmic1: at addr 0x82 on iicbus1 rk_i2c2: mem 0xff3d0000-0xff3d0fff irq 41 on ofwbus0 iicbus2: on rk_i2c2 rk_iodomain0: mem 0xff320000-0xff320fff on rk_grf0 rk_iodomain1: mem 0-0xff76ffff,0-0xffff on rk_grf1 generic_timer0: irq 2,3,4,5 on ofwbus0 Timecounter "ARM MPCore Timecounter" frequency 24000000 Hz quality 1000 Event timer "ARM MPCore Eventtimer" frequency 24000000 Hz quality 1000 rk_tsadc0: mem 0xff260000-0xff2600ff irq 37 on ofwbus0 mmc_pwrseq0: on ofwbus0 rk_usb2phy0: mem 0-0xff76ffff,0-0xffff on rk_grf1 rk_usb2phy1: mem 0-0xff76ffff,0-0xffff on rk_grf1 rk_emmcphy0: mem 0-0xff76ffff,0-0xffff on rk_grf1 rk_typec_phy0: mem 0xff7c0000-0xff7fffff on ofwbus0 smbios0: smbios0: Entry point: v3 (64-bit), Version: 3.7 cpulist0: on ofwbus0 cpu0: on cpulist0 cpufreq_dt0: on cpu0 cpufreq_dt0: Found cpu-supply cpufreq0: on cpu0 cpufreq_dt1: on cpu1 cpufreq_dt1: Found cpu-supply cpufreq1: on cpu1 cpufreq_dt2: on cpu2 cpufreq_dt2: Found cpu-supply cpufreq2: on cpu2 cpufreq_dt3: on cpu3 cpufreq_dt3: Found cpu-supply cpufreq3: on cpu3 cpufreq_dt4: on cpu4 cpufreq_dt4: Found cpu-supply cpufreq4: on cpu4 cpufreq_dt5: on cpu5 cpufreq_dt5: Found cpu-supply cpufreq5: on cpu5 pmu0: irq 0 on ofwbus0 pmu1: irq 1 on ofwbus0 rockchip_dwmmc0: mem 0xfe310000-0xfe313fff irq 10 on ofwbus0 rockchip_dwmmc0: Hardware version ID is 270a rockchip_dwmmc0: Disabling HS200+ (tuning code not written) rockchip_dwmmc1: mem 0xfe320000-0xfe323fff irq 11 on ofwbus0 rockchip_dwmmc1: Hardware version ID is 270a mmc0: on rockchip_dwmmc1 rockchip_dwmmc1: Disabling HS200+ (tuning code not written) sdhci_rockchip0: mem 0xfe330000-0xfe33ffff irq 12 on ofwbus0 rk_emmcphy0: got emmcclk clock sdhci_rockchip0-slot0: Hardware doesn't specify timeout clock frequency, setting BROKEN_TIMEOUT quirk. sdhci_rockchip0: 1 slot(s) allocated mmc1: on sdhci_rockchip0 ehci0: mem 0xfe380000-0xfe39ffff irq 13 on ofwbus0 usbus0: EHCI version 1.0 usbus0 on ehci0 ohci0: mem 0xfe3a0000-0xfe3bffff irq 14 on ofwbus0 usbus1 on ohci0 ehci1: mem 0xfe3c0000-0xfe3dffff irq 15 on ofwbus0 usbus2: EHCI version 1.0 usbus2 on ehci1 ohci1: mem 0xfe3e0000-0xfe3fffff irq 16 on ofwbus0 usbus3 on ohci1 rk_dwc30: on ofwbus0 snps_dwc3_fdt0: mem 0xfe800000-0xfe8fffff irq 88 on rk_dwc30 snps_dwc3_fdt0: 64 bytes context size, 32-bit DMA usbus4: trying to attach usbus4 on snps_dwc3_fdt0 iicbus0: at addr 0x28 iicbus0: at addr 0x90 iic0: on iicbus0 uart0: mem 0xff180000-0xff1800ff irq 28 on ofwbus0 uart0: debug port (-1,n,8,1) uart1: <16750 or compatible> mem 0xff1a0000-0xff1a00ff irq 30 on ofwbus0 uart1: console (1500000,n,8,1) uart2: <16750 or compatible> mem 0xff1b0000-0xff1b00ff irq 31 on ofwbus0 spi0: mem 0xff1d0000-0xff1d0fff irq 33 on ofwbus0 spibus0: on spi0 mx25l0: at cs 0 mode 0 on spibus0 mx25l0: Unknown SPI flash device. Vendor: 25, device id: 7018 device_attach: mx25l0 attach returned 6 iic1: on iicbus1 iicbus2: at addr 0x44 iicbus2: at addr 0xd0 iicbus2: at addr 0x38 iicbus2: at addr 0x18 iic2: on iicbus2 pwm0: mem 0xff420000-0xff42000f on ofwbus0 pwmbus0: on pwm0 pwmc0: channel 0 on pwmbus0 pwm1: mem 0xff420020-0xff42002f on ofwbus0 pwmbus1: on pwm1 pwmc1: channel 0 on pwmbus1 i2s0: mem 0xff880000-0xff880fff irq 58 on ofwbus0 Cannot set frequency for clk: clkin_i2s, error: 34 Cannot set frequency for clk: xin24m, error: 34 gpioc0: on gpio0 gpioc1: on gpio1 gpioc2: on gpio2 gpioc3: on gpio3 gpioc4: on gpio4 pwm_backlight0: on ofwbus0 gpioled0: on ofwbus0 pcm0: on ofwbus0 simpleamp0: on ofwbus0 simpleamp0: no VCC supplyarmv8crypto0: Timecounters tick every 1.000 msec rk818_pmu0: registered as a time-of-day clock, resolution 1.000000s usbus0: 480Mbps High Speed USB v2.0 usbus1: 12Mbps Full Speed USB v1.0 ugen0.1: at usbus0 uhub0 on usbus0 uhub0: on usbus0 ugen1.1: at usbus1 uhub1 on usbus1 uhub1: on usbus1 usbus2: 480Mbps High Speed USB v2.0 usbus3: 12Mbps Full Speed USB v1.0 ugen2.1: at usbus2 uhub2 on usbus2 uhub2: on usbus2 ugen3.1: at usbus3 uhub3 on usbus3 uhub3: on usbus3 usbus4: 5.0Gbps Super Speed USB v3.0 ugen4.1: at usbus4 uhub4 on usbus4 uhub4: on usbus4 uhub1: 1 port with 1 removable, self powered mmcsd0: 63GB at mmc0 50.0MHz/4bit/1016-block uhub3: 1 port with 1 removable, self powered GEOM: mmcsd0: the secondary GPT header is not in the last LBA. mmcsd1: 124GB at mmc1 25.0MHz/8bit/65535-block mmcsd1boot0: 4MB partition 1 at mmcsd1 mmcsd1boot1: 4MB partition 2 at mmcsd1 mmcsd1rpmb: 17MB partition 3 at mmcsd1 pcm0: no driver attached to codec node uhub0: 1 port with 1 removable, self powered Trying to mount root from ufs:/dev/ufs/FreeBSD_Install [rw,noatime]... CPU 0: ARM Cortex-A53 r0p4 affinity: 0 0 Cache Type = <64 byte CWG,64 byte ERG,64 byte D-cacheline,VIPT I-cache,64 byte I-cacheline> Instruction Set Attributes 0 = Instruction Set Attributes 1 = <> Instruction Set Attributes 2 = <> Processor Features 0 = Processor Features 1 = Processor Features 2 = <> Memory Model Features 0 = Memory Model Features 1 = <8bit VMID> Memory Model Features 2 = <32bit CCIDX,48bit VA> Memory Model Features 3 = <> Memory Model Features 4 = <> Debug Features 0 = Debug Features 1 = <> Auxiliary Features 0 = <> Auxiliary Features 1 = <> AArch32 Instruction Set Attributes 5 = AArch32 Media and VFP Features 0 = AArch32 Media and VFP Features 1 = CPU 1: ARM Cortex-A53 r0p4 affinity: 0 1 CPU 2: ARM Cortex-A53 r0p4 affinity: 0 2 CPU 3: ARM Cortex-A53 r0p4 affinity: 0 3 CPU 4: ARM Cortex-A72 r0p2 affinity: 1 0 Cache Type = <64 byte CWG,64 byte ERG,64 byte D-cacheline,PIPT I-cache,64 byte I-cacheline> Memory Model Features 0 = CPU 5: ARM Cortex-A72 r0p2 affinity: 1 1 gic0: using for IPIs Release APs...done WARNING: WITNESS option enabled, expect reduced performance. Unresolved linked clock found: clkin_gmac uhub4: 2 ports with 2 removable, self powered GEOM: diskid/DISK-4490029E: the secondary GPT header is not in the last LBA. uhub2: 1 port with 1 removable, self powered Dual Console: Video Primary, Serial Secondary GEOM: diskid/DISK-4490029E: the secondary GPT header is not in the last LBA. GEOM: diskid/DISK-4490029E: the secondary GPT header is not in the last LBA. warning: KLD '/boot/kernel/kernel' is newer than the linker.hints file KLD mx25l.ko: depends on kernel - not available or version mismatch lo0: link state changed to UP lock order reversal: (sleepable after non-sleepable) 1st 0xffff00000158fcf0 dev mtx (devd, sleep mutex) @ /home/toby/Data/home/toby/Projects/freebsd-pinephonepro/freebsd-src/sys/kern/kern_devctl.c:571 2nd 0xffff0000016e2390 umareclaim (umareclaim, sx) @ /home/toby/Data/home/toby/Projects/freebsd-pinephonepro/freebsd-src/sys/vm/uma_core.c:3433 Freed UMA keg (DEVCTL) was not empty (399 items). Lost 100 pages of memory. goodix_touch0: at addr 0x28 irq 81 on iicbus0 goodix_touch0: Setting up evdev... goodix_touch0: Touchscreen size X: 720 goodix_touch0: Touchscreen size Y: 1440 goodix_touch0: Product ID: 1 1 5 8 goodix_touch0: F/w version: 0 1 goodix_touch0: X-res: 42 1 goodix_touch0: Y-res: 2 0 goodix_touch0: Vendor ID: 0 3 goodix_touch0: Goodix touch driver loaded FreeBSD/arm64 (PinePhonePro-FreeBSD) (ttyu1) login: root Last login: Thu Sep 24 16:07:52 from :0 FreeBSD 15.0-CURRENT (PINEPHONE_PRO) #75 main-b836c229aa5a-dirty: Wed Apr 16 15:16:46 SAST 2025 Welcome to FreeBSD! Release Notes, Errata: https://www.FreeBSD.org/releases/ Security Advisories: https://www.FreeBSD.org/security/ FreeBSD Handbook: https://www.FreeBSD.org/handbook/ FreeBSD FAQ: https://www.FreeBSD.org/faq/ Questions List: https://www.FreeBSD.org/lists/questions/ FreeBSD Forums: https://forums.FreeBSD.org/ Documents installed with the system are in the /usr/local/share/doc/freebsd/ directory, or can be installed later with: pkg install en-freebsd-doc For other languages, replace "en" with a language code like de or fr. Show the version of FreeBSD installed: freebsd-version ; uname -a Please include that output and any error messages when posting questions. Introduction to manual pages: man man FreeBSD directory layout: man hier To change this login announcement, see motd(5). root@PinePhonePro-FreeBSD:~ # sysctl hw.acpi.battery hw.acpi.battery.millivolts: 3840 hw.acpi.battery.rate: -216 hw.acpi.battery.status: 0 hw.acpi.battery.life: 92 hw.acpi.battery.units: 1 root@PinePhonePro-FreeBSD:~ # ``` 2026-10-04: FreeBSD boots from microSD card, if I select the updated u-boot from the rk2aw menu (choice 3). 2026-10-04: I created this page.