Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 4.8-STABLE #0: Fri Oct  3 21:38:01 CEST 2003
    root@kg-omni2.kg4.no:/usr/obj/usr/src/sys/TP380_FW
Calibrating clock(s) ... TSC clock: 167064086 Hz, i8254 clock: 1193315 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254"  frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium/P55C (167.05-MHz 586-class CPU)
  Origin = "GenuineIntel"  Id = 0x543  Stepping = 3
  Features=0x8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,MMX>
real memory  = 83886080 (81920K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00590000 - 0x04ff7fff, 78020608 bytes (19048 pages)
avail memory = 75988992 (74208K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00fd850
bios32: Entry = 0xfd860 (c00fd860)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0x0
pnpbios: Found PnP BIOS data at 0xc00fe700
pnpbios: Entry = f0000:e724  Rev = 1.0
pnpbios: Event flag at 415
Other BIOS signatures found:
ACPI: 00000000
Preloaded elf kernel "kernel" at 0xc0569000.
Intel Pentium detected, installing workaround for F00F bug
Creating DISK md0
md0: Malloc disk
Math emulator present
pci_open(1):	mode 1 addr port (0x0cf8) is 0x80000050
pci_open(1a):	mode1res=0x80000000 (0x80000000)
pci_cfgcheck:	device 0 [class=060000] [hdr=00] is there (id=12358086)
pcibios: No call entry point
npx0: <math processor> on motherboard
npx0: INT 16 interface
i586_bzero() bandwidth = 174947515 bytes/sec
bzero() bandwidth = 700280112 bytes/sec
pcib0: <Host to PCI bridge> on motherboard
found->	vendor=0x8086, dev=0x1235, revid=0x02
	class=06-00-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
found->	vendor=0x8086, dev=0x1234, revid=0x03
	class=06-80-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
found->	vendor=0x10c8, dev=0x0003, revid=0x02
	class=03-00-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=11
	map[10]: type 1, range 32, base 08000000, size 22
found->	vendor=0x1013, dev=0x1100, revid=0x07
	class=06-05-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=255
	map[10]: type 1, range 32, base 000003e0, size  2
pci0: <PCI bus> on pcib0
chip1: <PCI to Other bridge (vendor=8086 device=1234)> at device 1.0 on pci0
pci0: <NeoMagic MagicGraph 128ZV SVGA controller> (vendor=0x10c8, dev=0x0003) at 3.0 irq 11
pcic0: <Cirrus Logic PD6729/6730 PCI-PCMCIA Bridge> port 0x3e0-0x3e3 at device 19.0 on pci0
pcic0: Polling mode
pcic0: PCI Configuration space:
  0x00: 0x11001013 0x040000c3 0x06050007 0x00000000 
  0x10: 0x000003e1 0x00000000 0x00000000 0x00000000 
  0x20: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x30: 0x00000000 0x00000000 0x00000000 0x000001ff 
  0x40: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x50: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x60: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x70: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x80: 0x00212007 0x00145189 0x00000000 0x00000000 
  0x90: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xa0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xb0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xc0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xd0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xe0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xf0: 0x00000000 0x00000000 0x00000000 0x00000000 
pccard0: <PC Card 16-bit bus (classic)> on pcic0
pccard1: <PC Card 16-bit bus (classic)> on pcic0
isa0: <ISA bus> on motherboard
ex_isa_identify()
pcic-: pcic0 exists, using next available unit number
pcic-: pcic1 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
pnpbios: 17 devices, largest 401 bytes
PNP0000: adding fixed io range 0x20-0x21, size=0x2, align=0x1
PNP0000: adding fixed io range 0xa0-0xa1, size=0x2, align=0x1
PNP0000: adding irq mask 00x4
PNP0000: end config
pnpbios: handle 0 device ID PNP0000 (0000d041)
PNP0200: adding fixed io range 0-0xf, size=0x10, align=0x1
PNP0200: adding fixed io range 0x80-0x8f, size=0x10, align=0x1
PNP0200: adding fixed io range 0xc0-0xdf, size=0x20, align=0x1
PNP0200: adding dma mask 0x10
PNP0200: end config
pnpbios: handle 1 device ID PNP0200 (0002d041)
PNP0100: adding irq mask 00x1
PNP0100: adding fixed io range 0x40-0x43, size=0x4, align=0x1
PNP0100: end config
pnpbios: handle 2 device ID PNP0100 (0001d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding fixed io range 0x70-0x71, size=0x2, align=0x1
PNP0b00: end config
pnpbios: handle 3 device ID PNP0b00 (000bd041)
PNP0800: adding fixed io range 0x61-0x61, size=0x1, align=0x1
PNP0800: end config
pnpbios: handle 4 device ID PNP0800 (0008d041)
PNP0303: adding irq mask 00x2
PNP0303: adding fixed io range 0x60-0x60, size=0x1, align=0x1
PNP0303: adding fixed io range 0x64-0x64, size=0x1, align=0x1
PNP0303: end config
pnpbios: handle 5 device ID PNP0303 (0303d041)
PNP0f13: adding irq mask 0x1000
PNP0f13: end config
pnpbios: handle 6 device ID PNP0f13 (130fd041)
PNP0c04: adding fixed io range 0xf0-0xff, size=0x10, align=0x1
PNP0c04: adding irq mask 0x2000
PNP0c04: end config
pnpbios: handle 7 device ID PNP0c04 (040cd041)
PNP0700: adding irq mask 0x40
PNP0700: adding io range 0x3f0-0x3f5, size=0x6, align=0
PNP0700: adding dma mask 0x4
PNP0700: end config
pnpbios: handle 8 device ID PNP0700 (0007d041)
PNP0600: adding irq mask 0x4000
PNP0600: adding io range 0x1f0-0x1f7, size=0x8, align=0
PNP0600: adding io range 0x3f6-0x3f7, size=0x2, align=0
PNP0600: end config
pnpbios: handle 9 device ID PNP0600 (0006d041)
PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0
PNP0a03: end config
pnpbios: handle 10 device ID PNP0a03 (030ad041)
PNP0c02: adding io range 0x2e-0x2f, size=0x2, align=0
PNP0c02: adding io range 0x92-0x92, size=0x1, align=0
PNP0c02: adding io range 0xb2-0xb3, size=0x2, align=0
PNP0c02: adding io range 0x4d0-0x4d1, size=0x2, align=0
PNP0c02: adding io range 0x15e8-0x15ef, size=0x8, align=0
PNP0c02: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c02: adding fixed memory32 range 0xf0000-0xfffff, size=0x10000
PNP0c02: adding fixed memory32 range 0x100000-0x40ffbff, size=0x3fffc00
PNP0c02: adding fixed memory32 range 0xffff0000-0xffffffff, size=0x10000
PNP0c02: end config
pnpbios: handle 11 device ID PNP0c02 (020cd041)
PNP0400: adding irq mask 0x80
PNP0400: adding io range 0x3bc-0x3bf, size=0x4, align=0
PNP0400: end config
pnpbios: handle 12 device ID PNP0400 (0004d041)
PNP0501: adding irq mask 0000
PNP0501: adding io range 0-0xffffffff, size=0, align=0
PNP0501: end config
pnpbios: handle 14 device ID PNP0501 (0105d041)
IBM0071: adding irq mask 0x10
IBM0071: adding io range 0x3f8-0x3ff, size=0x8, align=0x1
IBM0071: adding dma mask 0x8
IBM0071: end config
pnpbios: handle 15 device ID IBM0071 (71004d24)
CSC0011: adding io range 0x201-0x201, size=0x1, align=0
CSC0011: adding io range 0x534-0x537, size=0x4, align=0
CSC0011: adding io range 0x388-0x38b, size=0x4, align=0
CSC0011: adding io range 0x220-0x22f, size=0x10, align=0x1
CSC0011: adding irq mask 0x20
CSC0011: adding dma mask 0x2
CSC0011: adding dma mask 0x1
CSC0011: end config
pnpbios: handle 16 device ID CSC0011 (1100630e)
CSC0010: adding io range 0x538-0x53f, size=0x8, align=0
CSC0010: end config
pnpbios: handle 17 device ID CSC0010 (1000630e)
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x0000
ata0: mask=03 ostat0=50 ostat2=50
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 14 eb
ata0: mask=03 stat0=50 stat1=00
ata0-master: ATA 01 a5
ata0: devices=09
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x0000
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
adv0 failed to probe on isa0
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x330
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x334
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x230
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x234
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x130
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x134
bt0 failed to probe at port 0x134-0x137 on isa0
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0 failed to probe at port 0x134-0x137 on isa0
aic0 failed to probe at port 0x140-0x15f on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0045
atkbd: keyboard ID 0x54ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0045
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic1: Cannot get I/O range
pcic1 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic2: not probed (disabled)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: irq maps: 0x41 0x41 0x41 0x41
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port found at 0x3bc
ppc0: cannot reserve I/O port range
ppc0: <Parallel port> failed to probe at port 0x3bc-0x3c3 irq 7 on isa0
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
cs0: not probed (disabled)
sn0: not probed (disabled)
mss_probe: no address given, try 0x530
mss_detect - chip revision 0x0a
mss_detect() - Detected CS4236
pcm0: <CS4236> at port 0x530-0x537,0xf8c-0xf94,0xe0e irq 5 drq 1 flags 0xa102 on isa0
pcm0: sndbuf_setmap c000, 1000; 0xc69bf000 -> c000
pcm0: sndbuf_setmap d000, 1000; 0xc69c0000 -> d000
isa_probe_children: probing PnP devices
unknown: <PNP0000> can't assign resources
unknown: <PNP0000> at port 0x20-0x21,0xa0-0xa1 irq 2 on isa0
adv1: Invalid baseport of 0x0 specified. Nearest valid baseport is 0x100.  Failing probe.
unknown: <PNP0200> failed to probe at port 0-0xf,0x80-0x8f,0xc0-0xdf drq 4 on isa0
adv1: Invalid baseport of 0x40 specified. Nearest valid baseport is 0x100.  Failing probe.
unknown: <PNP0100> failed to probe at port 0x40-0x4f irq 0 on isa0
adv1: Invalid baseport of 0x70 specified. Nearest valid baseport is 0x100.  Failing probe.
unknown: <PNP0b00> failed to probe at port 0x70-0x7f irq 8 on isa0
adv1: Invalid baseport of 0x61 specified. Nearest valid baseport is 0x100.  Failing probe.
unknown: <PNP0800> failed to probe at port 0x61 on isa0
unknown: <PNP0303> can't assign resources
unknown: <PNP0303> at port 0x60 on isa0
unknown: <PNP0f13> can't assign resources
unknown: <PNP0f13> at irq 12 on isa0
adv1: Invalid baseport of 0xf0 specified. Nearest valid baseport is 0x100.  Failing probe.
unknown: <PNP0c04> failed to probe at port 0xf0-0xff irq 13 on isa0
unknown: <PNP0700> can't assign resources
unknown: <PNP0700> at port 0x3f0-0x3f5 on isa0
unknown: <PNP0600> can't assign resources
unknown: <PNP0600> at port 0x1f0-0x1f7 on isa0
adv1: Invalid baseport of 0xcf8 specified. Nearest valid baseport is 0x330.  Failing probe.
unknown: <PNP0a03> failed to probe at port 0xcf8-0xd07 on isa0
adv1: Invalid baseport of 0x2e specified. Nearest valid baseport is 0x100.  Failing probe.
unknown: <PNP0c02> failed to probe at port 0x2e-0x3d,0x92,0xb2-0xb3,0x4d0-0x4d1,0x15e8-0x15ef iomem 0-0x9ffff,0xf0000-0xfffff,0x100000-0x40ffbff,0xffff0000-0xffffffff on isa0
adv1: Invalid baseport of 0x3bc specified. Nearest valid baseport is 0x330.  Failing probe.
ppc1: using normal I/O port range
ppc1: SPP
ppc1: <Standard parallel printer port> at port 0x3bc-0x3bf irq 7 on isa0
ppc1: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> at port 0x10 on isa0
unknown: <IBM0071> can't assign resources
unknown: <IBM0071> at port 0x3f8-0x3ff on isa0
unknown: <CSC0011> can't assign resources
unknown: <CSC0011> at port 0x201,0x534-0x537 on isa0
adv1: Invalid baseport of 0x538 specified. Nearest valid baseport is 0x330.  Failing probe.
unknown: <CSC0010> failed to probe at port 0x538-0x547 on isa0
BIOS Geometries:
 0:03fdff3f 0..1021=1022 cylinders, 0..255=256 heads, 1..63=63 sectors
 0 accounted for
Device configuration finished.
IP packet filtering initialized, divert enabled, rule-based forwarding enabled, default to deny, logging limited to 100 packets/entry by default
bpf: lo0 attached
bpf: ppp0 attached
new masks: bio 68c040, tty 6310b2, net 6710b2
bpf: sl0 attached
bpf: faith0 attached
Creating DISK ad0
pcic0: Power: Vcc=0 Vpp=0
pcic0: Power applied
Power complete.
pcic0: Power: Vcc=-1 Vpp=-1
pcic0: Autodetected 5.0V card
pcic0: Power applied
pcic0: Output enabled
pcic0: Settling complete
Power complete.
pccard: card inserted, slot 0
pcic0: reset 1 int is 0 stat is df
ar: FreeBSD check1 failed
ad0: <HITACHI_DK23EA-40/00K3A0A2> ATA-5 disk at ata0-master
ad0: 38154MB (78140160 sectors), 77520 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, BIOSPIO
ad0: piomode=4 dmamode=2 udmamode=5 cblid=0
ata0-slave: piomode=4 dmamode=2 udmamode=-1 dmaflag=1
acd0: <HITACHI CDR-S100/0038> CDROM drive at ata0 as slave
acd0: read 2067KB/s (50012KB/s), 128KB buffer, BIOSPIO
acd0: Reads: CD-R, CD-DA stream, packet
acd0: Writes:
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
Mounting root from ufs:/dev/ad0s1a
ad0s1: type 0xa5, start 63, end = 78140159, size 78140097 : OK
start_init: trying /sbin/init
pcic0: reset 2 int is 60 stat is df
pcic0: reset 3 int is 60 stat is ff
splash: image decoder found: daemon_saver
Linux ELF exec handler installed
pccard0: Assigning ed1: io 0x300-0x31f irq 3 flags 0x0
pcic: I/O win 0 flags 15 300-31f
pcic: I/O win 0 flags 5 300-31f
ed1 at port 0x300-0x31f irq 3 slot 0 on pccard0
pcic: I/O win 0 flags 15 300-31f
bpf: ed1 attached
ed1: address 00:10:60:08:1d:00, type NE2000 (16 bit) 
module_register: module miibus/ukphy already exists!
linker_file_sysinit "miibus.ko" failed to register! 17